Finite Element Analysis On T-Type Bone Plate Using Stainless Steel 316l
DOI:
https://doi.org/10.29103/micoms.v4i.887Keywords:
Mechanical Properties, Thermal Properties, Bone Plate, Finite Element AnalysisAbstract
Bone fractures refer to the phenomenon of bone breakage or detachment caused by intensive loads. The primary causes of bone damage include incidents, traffic accidents, and sports injuries. One of the materials commonly used for bone support applications is 316L stainless steel. The design process for T-type bone supports involves creating mechanical drawings and simulations to demonstrate the material's behavior when subjected to mechanical and thermal loads during use by patients.In this study, the researchers aim to examine the mechanical and thermal properties of T-type bone plates using the Finite Element Analysis (FEA) method. The technical drawing of the T-type bone support is developed in Autodesk Fusion 360. The simulations involve the application of static and thermal loads. The loads applied to the T-type bone plate include compressive forces of 1 N, 10 N, 50 N, 85 N and 500 N, as well as temperatures of 28°C, 500°C, 800°C, 950°C, and 1400°C. The smallest stress is observed at a force of 1 N, resulting in a stress of 4.64 MPa, while the highest stress is recorded at a force of 500 N, producing a stress of 2319.70 MPa. Forces below 50 N are considered the safest to avoid deformation during loading. Additionally, temperatures below 912°C are optimal for the operation of bone supports.
References
[1] Chancharoen, P., Tangpornprasert, P., Amarase, C., Tantavisut, S., & Virulsri, C. (2024). Design of osteosynthesis plate for detecting bone union using wire natural frequency. Scientific Reports, 14(1). https://doi.org/10.1038/s41598-024-63530-w
[2] Mehboob, A., Barsoum, I., Mehboob, H., Abu Al-Rub, R. K., & Ouldyerou, A. (2024). Topology optimization and biomechanical evaluation of bone plates for tibial bone fractures considering bone healing. Virtual and Physical Prototyping, 19(1). https://doi.org/10.1080/17452759.2024.2391475
[3] Fikri, A., Wahyudin, U., & Purnama, A. (2021). ANALISIS POLA LAS SPIRAL PADA PENGELASAN GMAW TERHADAP KEKUATAN TARIK PADA BAJA KARBON RENDAH (Vol. 2, Issue 2).
[4] William D. Callister Jr., & David G. RethWistch. (2017). Material Science and Engineering an Introduction (10th ed.).
[5] Rizky, T., Fikri, A., & Nana Nasuha, C. (2022). Kekuatan Tarik Plywood Dari Bahan Sengon (Albizia Chinensis) (Vol. 3, Issue 2).
[6] Szewczyk, D., & Ramos, M. A. (2022). Low Temperature Thermal Properties of Nanodiamond Ceramics. Crystals, 12(12), 1774. https://doi.org/10.3390/cryst12121774
[7] Cui, Y., Chen, Y., Zhao, L., Zhu, F., Li, L., Kong, Q., & Chen, M. (2023). Investigation on the Properties of Flame-Retardant Phase Change Material and Its Application in Battery Thermal Management. Energies, 16(1), 521. https://doi.org/10.3390/en16010521
[8] William D. Callister Jr., & David G. RethWistch. (2017). Material Science and Engineering an Introduction (10th ed.).
[10] Zhang, G., Li, J., Shangguan, C., Zhou, X., Zhou, Y., & Huang, A. (2024). A metamaterial bone plate for biofixation based on 3D printing technology. International Journal of Bioprinting, 0(0), 2388. https://doi.org/10.36922/ijb.2388
[9] Ceddia, M., Solarino, G., Tucci, M., Lamberti, L., & Trentadue, B. (2024). Stress Analysis of Tibial Bone Using Three Different Materials for Bone Fixation Plates. Journal of Composites Science, 8(9), 334. https://doi.org/10.3390/jcs8090334
[11] Jin, K., Song, G., Diao, H., Zhang, X., Ji, X., Zhang, J., & Zhang, J. (2023). Hydrogen-bond assisted nonconventional photoluminescence of crystalline and amorphous cellulose. Cellulose, 30(13), 8139–8150. https://doi.org/10.1007/s10570-023-05392-5
[12] Khaleel Faraj, A., & Abdul Hussein, H. A. H. (2023). Application of Finite Element Technique: A Review Study. Iraqi Journal of Chemical and Petroleum Engineering, 24(1), 113–124. https://doi.org/10.31699/IJCPE.2023.1.13
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Ahmad Fikri, Desvina Yulisda, Agam Muarif, Rizka Mulyawan, Agus Adi Nursalim, Balqis Yafis, Sylvie Anastasya Utami, Apriani Riski
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
COPYRIGHT NOTICE
Authors retain copyright and grant the journal right of first publication and this work is licensed under a Creative Commons Attribution-ShareAlike 4.0 that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
All articles in this journal may be disseminated by listing valid sources and the title of the article should not be omitted. The content of the article is liable to the author.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
In the dissemination of articles, the author must declare https://proceedings.unimal.ac.id/micoms/index as the first party to publish the article.
